The Zulus of South Africa have a proverb about the importance of getting the job done.
Ungexoshe mpalambili, which means, “You can’t chase two antelopes at once.” As you concentrate your energies on one buck, the other gets away. In other words, focus on one target — the best one.
In South Africa, that target is to build residences and commercial structures more efficiently. To do so, more and more engineers and builders are opting for cold-formed steel (CFS) framing systems over conventional building methods.
“South Africa is having success with CFS systems,” said Don Allen, P.E., Director of Engineering at Super Stud Building Products, Inc. In 2012, Allen visited South Africa, where he met with engineers and builders and saw the rainbow nation’s use of CFS framing firsthand.
A great place for CFS framing
South Africa has a variety of climates. Johannesburg feels like a mid-Atlantic city. Durbin is tropical with palm trees. Cape Town is coastal. Mountains comprise much of the terrain.
“I saw beautiful homes with panoramic views from their verandas,” said Allen of his trip to the country.
South Africa’s backlog in housing and resulting need for rapid development make CFS framing extremely well suited for the region, according to Allen. “The frame of an affordable light-steel frame house can be made in hours in the factory. It’s transported to site and erected,” Allen said. “The entire house can be completed in a couple of weeks with very little waste.”
An upscale home under construction in South Africa features cold-formed steel.
Cost savings of 20 percent
In a recent article in South Africa’s Engineering News, John Barnard, Director of the Southern African Light Steel Frame Building Association (SAFSA), said that masonry construction is “dusty, noisy, and labor-intensive.”
In contrast, CFS — or, light-steel frame building (LSFB) as it’s known in South Africa — installs quickly, occupies little room on site, helps to keep trade traffic down, and offers long-term energy efficiency benefits, Barnard said.
CFS’s benefits “are staggering when compared with conventional building methods,” noted a SASFA media release issued prior to Allen’s South Africa visit. “Reduced wastage, lower logistical costs and reduced time of construction could offer cost savings of up to 20 percent, compared with conventional building.”
Lighter weight CFS
Allen said that South Africa uses the Australian/New Zealand design code. That code has similarities to the CFS framing provisions contained in the American Iron and Steel Institute’s AISI S100 standard.
However, there are some differences in how South African designers and builders use CFS.
5 differences in South African CFS use:
- Instead of using 8” or 10” deep box or back-to-back headers over door and window openings, South African designers and builders use a type of “mini truss” header. It’s made of track, top and bottom, with diagonals that look like the diagonals in North American open-web floor truss systems.
- Extra layers of track. For longer spans or heavier loads on these built-up headers and joists, the top and bottom track doesn’t have enough shear capacity to transfer the required loads, so South African designers add an extra layer of track or flat plates on both sides of the headers.
- South Africans build diagonals into the wall panels. Just about every panel has some sort of CFS diagonal, to provide lateral strength and help keep the panels square.
- South Africans tend to use CFS with different coatings. Allen said magnesium oxide sheathing is more common in South Africa than in North America, replacing gypsum board finishes.
- Thinner steel, higher yield strength. South African structural CFS is typically 0.8 mm thick, but sometimes goes up to 1.2 mm. But that’s the limit due to South African roll former machines. They are able to get strength for longer spans and higher loads by using high yield strength steel.
Some structural CFS studs and tracks in South Africa are thinner than structural members in North America.
Struggling to rise beyond 3 stories
Because South Africa uses a lighter weight CFS than what’s common in North America, building heights tend to be limited to two or three stories, Allen said.
“If we need a floor system with a 14” or 16” deep joist, we call up a roll former to make that joist, but most places in South Africa can’t do that,” Allen said. “They don’t use the heavier roll framer machines that we have in North America.”
“Thicker coils are available in South Africa, but they just don’t have many machines that can handle it” Allen said. “Perhaps in time the South Africans will make use of the techniques we use here to build mid-rise structures seven, eight, and nine stories high using CFS load-bearing framing.”
Allen said that there’s vast potential in South Africa to go higher with CFS by using thicker material. It’s up to the big players in the South African steel industry to do more to promote CFS, he said.
“But I give them credit,” Allen said. “They’ve found a way — even though it’s labor intensive — with small machines to build some decent-span floors, some heavy-duty floors, using cold-formed steel framing.”
“We can learn from the South Africans as we develop new products for the North American market,” Allen said. “By using higher yield-strength steels, tailored to specific applications, we can get greater spans out of products and truss-framed systems, and use less steel in the process, which can help reduce the cost of steel-framed systems.”
South African CFS floor joists use lightweight material, but South African engineering techniques allow them to span long distances.
Want to learn how cold-formed steel can benefit your next project? Request project assistance.
Many builders and architects say that cold-formed steel can only be used to frame buildings up to 10 stories – but this 40-story project may prove that wrong.
Cold-formed steel framing is among the most resilient of building materials. Understand CFS’ properties and how they factor into a building’s continued operation.
The structural integrity of CFS makes it viable for the construction of high-rise buildings.
The costs of using steel in construction rarely (if ever) are limited to the raw material itself. Ancillary elements to take into…